Setting default Values
It was mentioned, that edge parameter may be omitted and defaults will be used in this case. It is possible to set default values for the imported edges' number of lanes, allowed speed, and priority, using the options --default.lanenumber <INT> (or -L <INT> for short), --default.speed <FLOAT> (or -S <FLOAT> for short), --default.priority <INT> (or -P <INT> for short), respectively.
Normally, turnarounds are added as a possible edge continuations and play an important role during network building (see Publications#Krajzewicz_et_al2005_2). Still, one may want not to add them. In this cases, it is possible to disallow their appending using option --no-turnarounds.
Removing Geometry Nodes
In most input networks one may find nodes where one street comes in and one with the same attributes goes out or where two parallel edges come in and two (with the same attributes) come out. Such nodes have mostly no meaning (maybe besides the additional possibility to make a U-turn) and may be removed. The removal of such nodes increases the simulation speed due to a smaller number of edges to process during each time step. To remove such nodes and join the incoming and outgoing edges use --geometry.remove. The removal of nodes preserves the geometry of edges by ading a further geometry point at the removed node's position.
Using Edges' maximum Speed Definitions in km/h
Some people do not like to use speed definitions in m/s. If you want to define the speeds allowed on your edges in km/h instead, you should pass the option --speed-in-kmh to NETCONVERT.
Importing Networks without Traffic Light Logics
Some of the supported network formats supply information about the logic of the traffic lights, other do not. Due to this, we have to compute the traffic lights by our own. Doing this, we do not only have to compute the plans, but of course also, on which junction traffic lights are positioned. There are several options steering this procedure. At first, you have to tell NETCONVERT/NETGENERATE that you wish him to guess positions of traffic lights. This is done using the --tls.guess-option.
You may also set junctions as tls-controlled using --tls.set or as uncontrolled using --tls.unset. Both options assume to get a list of node names divided by ',' as parameter. The behaviour when a node is in both lists is undefined.
During the computation of tls-logics among other information we have to guess the duration of the phases. The options --tls.greent.time and --tls.yellow.time allow you to give the durations of green and yellow lights. Both options assume the duration in s as an int as parameter. The duration of having red is dependant to the number of other phases and their green and yellow phase durations. The green phase length has a default of 31s, yellow lights are - if no value is set for this option - computed using the --tls.yellow.min-decel - value described below.
There is yet no possibility to compute or estimate a "green wave" (synchronized traffic lights to allow continuous flow in one direction). You have only the options to shift the computed phases by half of their duration or by a quarter of their duration. The options for this are: --tls.half-offset and --tls.quarter-offset. Both options assume to get a list of node names divided by ',' as parameter. The behaviour when a node is in both lists or if the node is not meant to be controlled by a tls is undefined. Of course you can also edit the offsets within the generated network file (see Simulation/Traffic Lights).
Guessing On- and Off-Ramps
Most of the imported network descriptions do not have information about highway on- and off-ramps. You can force NETCONVERT to guess where on- and off-ramps shall be build. To enable this, use the option --ramps.guess. The algorithm assumes that an on-ramp shall be build on highway junctions with one incoming and one outgoing highway edge and one incoming minor edge and that an off-ramp shall be build on highway junctions with one incoming and one outgoing highway edge and one outgoing minor edge. You can constrain what a highway is by giving its minimum speed of this edge using --ramp.min-highway-speed and what a minor edge is by giving its maximum speed using --ramps.max-ramp-speed. Both options assume a float parameter being the speed. Furthermore, --ramp.ramp-length tells NETCONVERT how long the added ramp shall be in meters.
If you already know SUMO or if you have taken a look at some of the examples you may have noticed that vehicles used to "jump" over a junction instead of driving over them. This behaviour was quite appropriate for simulating large scenarios as in these cases the simulation error could be neglected (at least we have neglected it). Since version 0.10.0 SUMO will by default simulate traffic over the junctions in a way you know it from reality. Because inserting inner lanes into a network dramatically increases the network's size, you may want to return to the old behavior using the option --no-internal-links.
Pruning the imported network
NETCONVERT offers you some possibilities to constrain the read edges what is quite needful if one has a large street network but only wants to simulate a part of it or only the major roads. The first possibility to constrain the input is to name all the edges you want to keep. You can either do this on the command line/within your configuration directly using --keep-edges.explicit <ID>[,<ID>]* where each <ID> represents the id of an edge you want to keep or you can save this list into a file where each id is stored in a seperate line and then let NETCONVERT read this file using --keep-edges.input-file <FILE>. In the case you are joining edges using --geometry.remove (see "Removing Geometry Nodes"), you may also be interested in the option --keep-edges.postload which forces NETCONVERT to join the edges first and remove the unwished afterwards.
It is also possible to constrain the imported edges by giving a minimum velocity that is allowed on an edge in order to include this edge into the generated network. Use --keep-edges.min-speed <FLOAT> for this where <FLOAT> is the minimum velocity an edge must allow in order to be included in the output in m/s.